search

Cisco Systems MGX-FRSM-2T3E3 Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Sítě Cisco Systems MGX-FRSM-2T3E3. Cisco Systems MGX-FRSM-2T3E3 User's Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 54
  • Tabulka s obsahem
  • KNIHY
    • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
CHAPTER
Card and Service Configuration 6-1
6
Card and Service Configuration
This chapter describes how to configure the MGX 8850 cards and the services they support.
Although the presumption for this chapter is that a plan exists for your network, it reviews some of
the information that supports network planning. Generic instructions for inserting and removing
cards appear in “Chapter 4, “Enclosure and Card Installation.”
The services and applicable modules described in this chapter are:
• Physical and logical configuration of a broadband interface on the Processor Switching Module
(PXM) and, for a stand-alone switch, connection addition
• ATM service on the MGX-AUSM/B
• Frame Relay service on the following service modules:
MGX-FRSM-2CT3
MGX-FRSM-2T3E3
MGX-FRSM-HS2
MGX-FRSM-HS1/B
AX-FRSM-8T1 and AX-FRSM-8E1
• Circuit emulation service on the MGX-CESM-8T1 and MGX-CESM-8E1
• Redundancy and bulk distribution on the Service Resource Module-3T3 (MGX-SRM-3T3/B)
Note For information on the Route Processor Module (RPM), see the Cisco Route Processor
Module Installation and Configuration Guide.
Tasks for Configuring Cards and Services
This section contains a general description of the sequence of tasks for configuring the cards and
their services. It also contains details on how to configure resource partitions and add local
connections and three-segment connections. Detailed descriptions of these tasks for individual cards
appear in subsequent sections.
Modifying the Resource Partitioning
A resource partition at the card level consists of a number of logical connections (LCNs). At the port
level, a resource partition consists of a percentage of bandwidth, a DLCI or VPI/VCI range, and the
number of logical connection numbers (LCNs) available to a network control application. On the
Zobrazit stránku 0
1 2 3 4 5 6 ... 53 54

Shrnutí obsahu

Strany 1

CHAPTER Card and Service Configuration 6-16Card and Service ConfigurationThis chapter describes how to configure the MGX 8850 cards and the services t

Strany 2 - Rules for Adding Connections

The Processor Switching ModuleCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-10Step 3 As needed, specify usage

Strany 3

Card and Service Configuration 6-11Adding Connections on a PXM in a Stand-Alone NodeTable 6-1 Policing Definitions According to Policing and Connecti

Strany 4

ATM Universal Service ModuleCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-12ATM Universal Service ModuleThe e

Strany 5

Card and Service Configuration 6-13Using the CLI to Configure the Card, Lines, and PortsOn the CLI of the AUSM/B:Step 1 If necessary, modify the reso

Strany 6

ATM Universal Service ModuleCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-14cnfportrscprtn <port_num> &

Strany 7

Card and Service Configuration 6-15Adding and Configuring Connections on the AUSM/BOn the CLI of the AUSM/B:Step 1 Execute the addcon command. When y

Strany 8

ATM Universal Service ModuleCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-16cnfupcvbr has the same syntax and

Strany 9

Card and Service Configuration 6-17Adding and Configuring Connections on the AUSM/Bcnfupcubr <port.vpi.vci> <enable> <pcr[0+1]> <

Strany 10

ATM Universal Service ModuleCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-18Step 4 If necessary, change the q

Strany 11

Card and Service Configuration 6-19Frame Service Module FeaturesFrame Service Module FeaturesThis section describes the features available on each of

Strany 12 - ATM Universal Service Module

Tasks for Configuring Cards and ServicesCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-2PXM, the connections a

Strany 13

Frame Service Module FeaturesCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-20Four-Port Unchannelized Frame Se

Strany 14

Card and Service Configuration 6-21Frame Service Module Features• Standards-based management tools. Each FRSM supports SNMP, TFTP for configuration a

Strany 15

Frame Service Module FeaturesCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-22MGX-FRSM-HS2/B FeaturesThe speci

Strany 16

Card and Service Configuration 6-23Description of Connection Types on the FRSMDescription of Connection Types on the FRSMThe following sections descr

Strany 17

Description of Connection Types on the FRSMCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-24PVC Status Managem

Strany 18 - BPX 8600-to-BPX 8600 Segment

Card and Service Configuration 6-25Frame Relay-to-ATM Service Interworking• CLP is always 1.In the ATM-to-Frame Relay direction, you can specify a CL

Strany 19 - Frame Service Module Features

Description of Connection Types on the FRSMCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-26Command and Respon

Strany 20

Card and Service Configuration 6-27Configuring Frame Relay ServiceConfiguring Frame Relay ServiceThis section first describes how to configure the FR

Strany 21 - MGX-FRSM-2T3E3 Features

Configuring Frame Relay ServiceCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-28Table 6-2 Supported Lines rate

Strany 22 - Eight-Port FRSM Features

Card and Service Configuration 6-29Configuring the FRSM Cards, Lines, and Ports• line_num is the DS1 number in the range 1–56 to which you assign the

Strany 23

Card and Service Configuration 6-3Rules for Adding ConnectionsRules for Adding a DAX ConnectionA DAX con is a connection whose endpoints for the enti

Strany 24 - Cell Loss Priority

Configuring Frame Relay ServiceCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-30• lmi_sig specifies the LMI si

Strany 25 - Congestion Indication

Card and Service Configuration 6-31Adding a Frame Relay ConnectionNote The following step applies to Y-cable redundancy for the MGX-FRSM-2T3E3. For 1

Strany 26 - Loss Priority Indication

Configuring Frame Relay ServiceCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-32• mastership indicates if this

Strany 27

Card and Service Configuration 6-33Adding a Frame Relay Connection• CIR specifies the committed information rate. The range is 0–10000000 bps (althou

Strany 28

Configuring Frame Relay ServiceCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-34Establishing the BPX 8600-to-B

Strany 29

Card and Service Configuration 6-35Bit Error Rate Testing on an Unchannelized T3 or E3 FRSM• addchanloop and delchanloop are standard user commands f

Strany 30

Circuit Emulation Service Module for T3 and E3Cisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-36Circuit Emulati

Strany 31

Card and Service Configuration 6-37Configuring Service on a T3 or E3 CESMError and Alarm ResponseWhen it detects a loss of signal (LOS) alarm, the CE

Strany 32

Circuit Emulation Service Module for T3 and E3Cisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-38Configuring the

Strany 33

Card and Service Configuration 6-39Configuring Service on a T3 or E3 CESMcommand is addcon. If the application requires NSAP addressing, use addchan

Strany 34

Tasks for Configuring Cards and ServicesCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-4Rules for Adding Manag

Strany 35

Circuit Emulation Service Module for T3 and E3Cisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-40• route_priorit

Strany 36 - Cell Delay Treatment

Card and Service Configuration 6-41Eight-Port Circuit Emulation Service ModulesEight-Port Circuit Emulation Service ModulesThe main function of the C

Strany 37 - Error and Alarm Response

Eight-Port Circuit Emulation Service ModulesCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-42Cell Delay Treatm

Strany 38

Card and Service Configuration 6-43Configuring Service on an Eight-Port CESMConfiguring Service on an Eight-Port CESMThis section describes the steps

Strany 39

Eight-Port Circuit Emulation Service ModulesCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-44Step 3 Create a l

Strany 40

Card and Service Configuration 6-45Configuring Service on an Eight-Port CESMAdding and Modifying ConnectionsUse either the Cisco WAN Manager applicat

Strany 41

Eight-Port Circuit Emulation Service ModulesCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-46Step 2 Optionally

Strany 42

Card and Service Configuration 6-47Service Resource ModuleService Resource ModuleThis section describes how to use the features of the T3 version of

Strany 43

Service Resource ModuleCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-48Bulk Distribution for T1 ServiceThe MG

Strany 44

Card and Service Configuration 6-49Redundancy Support by the MGX-SRM-3T3/BThe need for back cards and the choice of bus for redundancy support depend

Strany 45

Card and Service Configuration 6-5The Processor Switching ModuleThe Processor Switching ModuleThis section first describes how to activate and config

Strany 46

Service Resource ModuleCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-50Configuring Redundancy Through the Dis

Strany 47 - Service Resource Module

Card and Service Configuration 6-51Bit Error Rate Testing Through an MGX-SRM-3T3The MGX 8850 bus structure supports one BERT session per upper or low

Strany 48

Service Resource ModuleCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-52Table 6-6 Loopback Test for AX-FRSM-8T

Strany 49

Card and Service Configuration 6-53Bit Error Rate Testing Through an MGX-SRM-3T3Pattern Test OptionsThe pattern test options consist of the device to

Strany 50

Service Resource ModuleCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-54Loopback Test OptionsThe loopback test

Strany 51

The Processor Switching ModuleCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-6Configuring Card-Level Parameter

Strany 52

Card and Service Configuration 6-7Automatic Protection Switching on the PXMUsing an example of 100% of the bandwidth on one logical port 1:addport 1

Strany 53 - • in-band/ESF

The Processor Switching ModuleCisco MGX 8850 Installation and Configuration, Release 1.1.00, Part Number 78-6186-026-8Initial APS specification consis

Strany 54 - Loopback Test Options

Card and Service Configuration 6-9Adding Connections on a PXM in a Stand-Alone NodeAdding Connections on a PXM in a Stand-Alone NodeThis section desc

Komentáře k této Příručce

Žádné komentáře
Související produkty a manuály pro Sítě Cisco Systems MGX-FRSM-2T3E3
Sítě Cisco Systems CATALYST 8500 Uživatelský manuál   (20 stránky)
Sítě Cisco Systems XR 12410 Instalační manuál   (230 stránky)
Sítě Cisco Systems Chassis AS5350 Instalační manuál   (102 stránky)
Sítě Cisco Systems ASA 5500 Uživatelský manuál   (16 stránky)
Sítě Cisco Systems OL-1377-02 Uživatelský manuál   (14 stránky)
Sítě Cisco Systems 1800 Series Rychlý návod   (4 stránky)
Sítě Cisco Systems SS7 Uživatelský manuál   (64 stránky)
Sítě Cisco Systems ASR 1000 Uživatelský manuál   (112 stránky)
Sítě Cisco Systems OL-7821-04 Uživatelský manuál   (131 stránky)
Sítě Cisco Systems A9K24X10GETR Rychlý návod   (142 stránky)
Sítě Cisco Systems 2130 Uživatelský manuál   (116 stránky)
Sítě Cisco Systems ACCESS OL-3597-01 Uživatelský manuál   (1 stránky)
Sítě Cisco Systems OL-5650-02 Uživatelský manuál   (122 stránky)
Sítě Cisco Systems OL-19806-03 Uživatelský manuál   (84 stránky)
Sítě Cisco Systems 78-16409-03 Uživatelský manuál   (24 stránky)
Sítě Cisco Systems PA-4R Uživatelský manuál   (42 stránky)
Sítě Cisco Systems WIC-1AM-V2 Uživatelský manuál   (24 stránky)
Sítě Cisco Systems MC-607 Uživatelský manuál   (54 stránky)
Sítě Cisco Systems EDFA2 Provozní příručka   (280 stránky)
Sítě Cisco Systems AS5200 Uživatelský manuál   (22 stránky)
  • Ayre HS Hirschler Contemporary Research Perreaux EMP Tek
  • Ford Kazetové přehrávače MS-Tech Napájecí jednotky Schneider Kuličková pera Phase One Bridge kamery Klark Teknik ne
  • Blaupunkt VELOCITY VR 6000 Char-Broil 12301719 Korg GB-1 Samsung 50X
  • Nikon MB-D12 Uživatelský manuál Canon PIXMA MG5420 Uživatelský manuál ILive ISP100B Uživatelský manuál Sennheiser EH250 Datový list AEG L8FER942C Uživatelský manuál