Cisco Systems CF2001P Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Tisk a skenování Cisco Systems CF2001P. Cisco Systems CF2001P User's Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 43
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
SETUP INSTRUCTIONS
CF2001P
4004-7715-01 © MINOLTA CO., LTD. Printed in Japan
Printer
WARNING
Do not plug in the power cord or turn on this unit until you are instructed to according to this manual.
CAUTION
Install this machine so that it can quickly be unplugged from the electrical outlet in case of an
emergency. The socket-outlet shall be installed near the machine and shall be easily accessible.
Keep all packing materials out of the reach of children.
NOTE
If the CF2001P is connected to the Minolta MircroPress Cluster Printing System, be sure
to take back the User Manual for the CF2001P, since it is not needed by the customer.
Keep all packing materials in a safe place for later use in case they are needed for transportation.
NEXT
Zobrazit stránku 0
1 2 3 4 5 6 ... 42 43

Shrnutí obsahu

Strany 1 - SETUP INSTRUCTIONS

SETUP INSTRUCTIONSCF2001P4004-7715-01 © MINOLTA CO., LTD. Printed in JapanPrinterWARNING• Do not plug in the power cord or turn on this unit until you

Strany 2

CF2001P– 9 –4004-7715-016. Fully pull the toner hopper shutter out toward you. Pulling out the toner hopper shutter allows the toner to begin filling

Strany 3

CF2001P– 10 –4004-7715-014. Connecting the Cables1. Make sure that the printer power cord is not plugged into the electrical outlet, and then insert t

Strany 4

CF2001P– 11 –4004-7715-016. Installing the Manual Holder1. Insert the tab on the bottom of the manual holder into the slot in the printer as shown in

Strany 5

CF2001P– 12 –4004-7715-015. Load the prepared A4(C)-size (or Letter(C)-size) plain paper into the paper drawer.6. Slide the adjustable paper guides ag

Strany 6

CF2001P– 13 –4004-7715-01 Setting Up the Converter (7)1. Remove the converter from its box.2. Remove the screw at the bottom of the con-verter, and th

Strany 7

CF2001P– 14 –4004-7715-01 Connecting the Equipment Cables1. Insert a connector on the DTP32 cable (4) into the I/O port on the side of the X-Rite, and

Strany 8

CF2001P– 15 –4004-7715-016. Loosen the screw of the terminal, and then attach the ground wire as shown. 7. Attach the upper cover of the converter.8.

Strany 9

CF2001P– 16 –4004-7715-014. Check that the External Panel Controller appears in the computer screen, and then display the Tech. Rep. Mode screen. (For

Strany 10 - NEXTNEXT

CF2001P– 17 –4004-7715-0111. Insert the auto-cal strip into the X-Rite.NOTEInsert the auto-cal strip after “INSERT CALSTRIP” appears on the X-Rite dis

Strany 11

CF2001P– 18 –4004-7715-0115. Feed the test pattern in direction “2” to read the row represented by “B”.When feeding the test pattern to read the row r

Strany 12

CF2001P– 1 –4004-7715-011. Outline of the CF2001P System Setup NOTE• Install and setup each option according to the instructions included with theopti

Strany 13

CF2001P– 19 –4004-7715-0121. Check that “Read the Pattern of Cyan” dis-appears, and that >> appears beside “Read the Pattern of Magenta”.NOTEIf

Strany 14

CF2001P– 20 –4004-7715-018. Making System Setting Checking the Date Setting1. Check that the External Panel Controller appears in the computer screen

Strany 15

CF2001P– 21 –4004-7715-01 Specifying the Serial NumberNOTEBe sure to specify the serial number.When the serial number is specified, the settings for e

Strany 16

CF2001P– 22 –4004-7715-01 Specifying Who Performs ReplacementsNOTEThe message that appears a unit must be replaced can be changed to indicatethat eith

Strany 17

CF2001P– 23 –4004-7715-01 Printing the List1. Prepare A4-size (or Letter-size) plain paper.2. Pull out the paper drawer for Tray 1.3. Press down on th

Strany 18

CF2001P– 24 –4004-7715-0110. Check that the External Panel Controller appears in the computer screen, and then display the Tech. Rep. Mode screen. (Fo

Strany 19

CF2001P– 25 –4004-7715-01 To set the “Energy Save Mode” parameterNOTEWhen making settings according to the customer’s requests, refer to the procedure

Strany 20

CF2001P– 26 –4004-7715-01 To set the “Sleep Mode” parameterNOTEWhen making settings according to the customer’s requests, refer to the proceduredescri

Strany 21

CF2001P– 27 –4004-7715-019. Loading PaperNOTEFor more details about loading paper, refer to the User Manual. Tray 11. Prepare paper that meets this p

Strany 22

CF2001P– 28 –4004-7715-01 Tray 21. Prepare paper that meets this product’s specifications.2. Pull out the paper drawer for Tray 2.3. Press down on the

Strany 23

CF2001P– 2 –4004-7715-012. Unpacking Unpacking the Accessories1. Remove the accessories from the box, and then check that the following are enclosed.

Strany 24

CF2001P– 29 –4004-7715-018. Affix the enclosed paper size label to Tray 2 as shown.9. Affix the enclosed drawer number label as shown.10.Adjusting the

Strany 25

CF2001P– 30 –4004-7715-014. Click [PRT Area].5. Click [Left Margin]. 6. Select the key for the paper drawer that is to be adjusted, and then click the

Strany 26

CF2001P– 31 –4004-7715-01 Adjusting the Paper Reference Position for PF-1181. Check that the External Panel Controller appears in the computer screen,

Strany 27

CF2001P– 32 –4004-7715-0110. Check that the message displayed in the control panel changes from “Alert Printing suspended” to “Info”.11. Exit the Exte

Strany 28

CF2001P– 33 –4004-7715-015. Click [Left Margin].6. Select the key for the third paper drawer, and then click the Start key in the External Panel Contr

Strany 29

CF2001P– 34 –4004-7715-015. Click [Dup. Left Margin].6. Click [1st.].7. Click the Start key in the External Panel Controller. A test page is printed.8

Strany 30

CF2001P– 35 –4004-7715-01 Checking the Hole-Punching Positions for FN-107NOTE• For details on the installing FN-107, refer to its Setup Instructions.•

Strany 31

CF2001P– 36 –4004-7715-01 Setting DT-105 (USA and Canada only)NOTE• For details on installing DT-105, refer to the Setup Instructions included with it

Strany 32

CF2001P– 37 –4004-7715-01<Precautions for Connecting a Telephone to the Data Terminal>• If a telephone is connected to the data terminal, check

Strany 33

CF2001P– 38 –4004-7715-012. Click [Dial Mode].3. Select the dial mode of the user’s telephone line.Push-button... [Tone]Rot

Strany 34

CF2001P– 3 –4004-7715-01 Removing the Protective Tape and Packing Materials<Outside Surface of the Printer>Remove the tape affixed to the outsid

Strany 35

CF2001P– 39 –4004-7715-01<Maintenance Center (Billing Center) Settings>NOTEThe procedure for making Maintenance Center settings are described be

Strany 36

CF2001P– 40 –4004-7715-01<DT Settings>1. Click [ID Code] so that it appears in white on a black background.2. Using the keypad in the External P

Strany 37

CF2001P– 41 –4004-7715-01<Setting the Telephone Number>1. Click [TEL No.] so that it appears in white on a black background.2. Click the Clear k

Strany 38

CF2001P– 42 –4004-7715-01<Initial Transmission>• To perform the initial user registration for the data terminal after the initial settings have

Strany 39

CF2001P– 4 –4004-7715-013. Installing the Units Installing the Imaging Units1. Grasp the handle of the front door, and then carefully swing the door

Strany 40

CF2001P– 5 –4004-7715-017. Remove the protective tape from the imag-ing unit.NOTEThe clear plastic protective sheet is notpacking material; therefore,

Strany 41

CF2001P– 6 –4004-7715-0112. Separate the top and bottom halves of the empty imaging unit cover.NOTESince the bottom half of the imaging unitcover will

Strany 42 - Saver key

CF2001P– 7 –4004-7715-012. Remove the two pieces of tape from the lock levers of the oil-coating unit shown.3. Remove the oil-coating unit from its bo

Strany 43 - <Initial Transmission>

CF2001P– 8 –4004-7715-01 Filling the TonerNOTE• The toner bottles are not included. A bottle of toner is needed for each color (fourin total) and shou

Komentáře k této Příručce

Žádné komentáře