Cisco Systems ISR4451XK9 Uživatelský manuál Strana 114
- Strana / 160
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
5-8
Hardware Installation Guide for the Cisco 4451-X Integrated Services Router
Chapter 5 ROM Monitor Overview and Basic Procedures
Exiting ROM Monitor Mode
DETAILED STEPS
Configuration Example
rommon 3 > confreg
Configuration Summary
(Virtual Configuration Register: 0x0)
enabled are:
[ 0 ] break/abort has effect
[ 1 ] console baud: 9600
boot: ...... the ROM Monitor
do you wish to change the configuration? y/n [n]: y
enable "diagnostic mode"? y/n [n]:
enable "use net in IP bcast address"? y/n [n]:
enable "load rom after netboot fails"? y/n [n]:
enable "use all zero broadcast"? y/n [n]:
disable "break/abort has effect"? y/n [n]:
enable "ignore system config info"? y/n [n]:
change console baud rate? y/n [n]:
change the boot characteristics? y/n [n]:
Configuration Summary
(Virtual Configuration Register: 0x0)
enabled are:
[ 0 ] break/abort has effect
[ 1 ] console baud: 9600
boot: ...... the ROM Monitor
do you wish to change the configuration? y/n [n]:
Command or Action Purpose
Step 1
confreg
Example:
rommon 1> confreg
Initiates the configuration register configuration prompts.
Step 2
Respond to each prompt as instructed.
See the example that follows this procedure for more
information
.
Step 3
reset
Example:
rommon 2> reset
Resets and initializes the router.
- Cisco Systems, Inc 1
- CONTENTS 3
- Contents 4
- 4 Initial Configuration 4-1 5
- Objectives 9
- Audience 9
- Organization 10
- Conventions 11
- Waarschuwing 12
- Varoitus 12
- Attention 12
- Avvertenza 13
- Advarsel 13
- ¡Advertencia! 13
- Varning! 13
- Related Documentation 17
- Searching for Cisco Documents 18
- About the Cisco ISR 4451-X 19
- Chassis Views 21
- Cisco ISR 4451-X Chassis 22
- Chassis Views 23
- Platform Summary 25
- Labels on Cisco ISR 4451-X 26
- Hardware Features 27
- Front Panel Ethernet Ports 28
- Dual Mode GE/SFP Ports 28
- USB Serial Console Port 28
- Front Panel PoE+ Ports 28
- LED Indicators 29
- Hardware Features 30
- External Slots 31
- Modules and Cards 33
- Power Supplies 34
- About Slots and Interfaces 35
- About Slots and Interfaces 36
- Slot Numbering 37
- Specifications 38
- Specifications 39
- Standard Warning Statements 44
- Standard Warning Statements 45
- Safety Recommendations 48
- Safety Recommendations 49
- General Site Requirements 50
- General Site Requirements 51
- Rack Requirements 52
- Console Port Connections 55
- Auxiliary Port Connections 56
- Ethernet Connections 57
- Installation Checklist 59
- Creating a Site Log 60
- What You Need to Know 63
- Before You Begin 63
- Unpacking the Router 64
- Installing the Router 64
- Rack-Mounting the Chassis 65
- Installing the Router 66
- Mounting the Router in a Rack 67
- Grounding the Chassis 69
- Statement 1032 70
- Chassis Grounding 71
- Connecting Power 72
- Connecting to AC Power 73
- • no parity 75
- • 1 stop bit 75
- • no flow control 75
- Using the Setup.exe program 78
- Statement 1001 80
- Ports and Cabling 82
- Initial Configuration 84
- Completing the Configuration 87
- Default Routes 96
- Default Network 96
- Gateway of Last Resort 96
- Configuration Examples 100
- SUMMARY STEPS 101
- DETAILED STEPS 101
- Prerequisites 102
- Examples 102
- ROM Monitor Overview 107
- Entering ROM Monitor Mode 108
- Environment Variable Settings 111
- Exiting ROM Monitor Mode 113
- Configuration Example 114
- Example of Upgrade 115
- Internal and External Modules 117
- Safety Warnings 118
- OL-27644-01 119
- Safety Warnings 119
- Accessing Internal Modules 120
- Overview 123
- LEDs on the NIM-SSD 124
- • 104°F (40°C) at sea level 125
- Solid State Drives (SSD) 126
- Restrictions 131
- Statement 94 132
- Locating and Orienting DIMM 134
- 1 Polarization notch 135
- Removing a DIMM 136
- Installing a DIMM 137
- Software Requirement for SMs 140
- Locating an SM or NIM 140
- Removing an SM or NIM 140
- Installing an SM 140
- Verifying SM Installation 141
- Statement 1073 144
- Statement 1030 144
- NIM in the Cisco ISR 4451-X 145
- ASR1000-RP1 147
- Replacing a Fan Tray 150
- Replacing a Fan Tray 151
- Installing SFP Modules 154
- Installing SFP Modules 155
- Laser Safety Guidelines 156
- Removing SFP Modules 156
- Statement 1051 157
- Hot-Swapping 159
- OIR Procedures 160
- Hot-Swapping Procedures 160
Související produkty a manuály pro Brány / ovladače Cisco Systems ISR4451XK9
(40 stránky)
(30 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.135 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce